- Navistar Engine Diagnostics (NEDS) Software 2023
$96.00Add to cart
- DOWNLOAD Caterpillar Electronic Technician ET 2019C
$41.00Add to cart
- DOOSAN diagnostic software DMS-5 3.1.3 [2023.11] 1PC
$106.00Add to cart
- Description
- Tags
- Reviews (0)
Description
Circuit Description
The aftertreatment diesel particulate filter temperature sensor module is a smart device that communicates with the engine control module via the J1939 data link. The aftertreatment diesel partculate filter temperature sensor module performs its own internal diagnostics and reports malfunctions back to the engine control module using the J1939 data link. The aftertreatment diesel particulate filter temperature sensor module is used to measure the aftertreatment diesel oxidation catalyst intake temperature, aftertreatment diesel particulate filter intake temperature, and aftertreatment diesel particulate filter outlet temperature. The temperature probes are permanently attached to the aftertreatment diesel particulate filter temperature sensor module and can not be replaced individually.
Component Location
The aftertreatment diesel particulate filter temperature sensor module is mounted on the aftertreatment diesel particulate filter.
Conditions for Running the Diagnostics
This diagnostic runs continuously when the keyswitch is in the ON position or when the engine is running.
Conditions for Setting the Fault Codes
The aftertreatment diesel particulate filter temperature sensor module reported high battery supply voltage.
Action Taken When the Fault Code is Active
The ECM illuminates the amber CHECK ENGINE lamp and/or the Malfunction Indicator Lamp (MIL) immediately when the diagnostic runs and fails.
Active and stationary regeneration of the diesel particulate filter will be disabled.
Engine torque will be reduced if the engine is operated for an extended period of time with this fault active.
Conditions for Clearing the Fault Code
To validate the repair, perform a key cycle, start the engine and let it idle for 1 minute.
The fault code status displayed by INSITE™ electronic service tool will change to INACTIVE immediately after the diagnostic runs and passes.
The ECM will turn off the amber CHECK ENGINE lamp immediately after the diagnostic runs and passes.
For On-Board Diagnostics (OBD) engines, the ECM will extinguish the Malfunction Indicator Lamp (MIL) after three consecutive trips where the diagnostic runs and passes.
The Reset All Faults command in INSITE™ electronic service tool can be used to clear active and inactive faults, as well as extinguish the MIL for OBD applications.
Shop Talk
Possible causes of this fault code include:
Incorrect Battery System Voltage setting in INSITE
Incorrect sensor for the application (12 VDC versus 24 VDC)
High battery voltage supply
Possible Cause:
1) Aftertreatment DPF temperature sensor module failure
2) ECM calibration
Related
Tags: , 2018, 3, 4161, 5742, Above, Aftertreatment, CM2450, Code, Cummins, Diesel, Fault, Filter, FMI, High, Module-, Newer, Normal, or, Particulate, PID, Sensor, Shorted, Source, SPN, Temperature, to, Voltage, X124B, X15
Reviews
There are no reviews yet.
Be the first to review “Cummins X15 CM2450 X124B (2018 & Newer) Fault Code: 4161 PID: SPN: 5742 FMI: 3 Aftertreatment Diesel Particulate Filter Temperature Sensor Module- Voltage Above Normal or Shorted to High Source”
Categories Cumminz, DTC TRUCKS, Tags , 2018, 3, 4161, 5742, Above, Aftertreatment, CM2450, Code, Cummins, Diesel, Fault, Filter, FMI, High, Module-, Newer, Normal, or, Particulate, PID, Sensor, Shorted, Source, SPN, Temperature, to, Voltage, X124B, X15
- DOWNLOAD Navistar Engine Diagnostics 2018 NED
$42.00Add to cart
See AlsoCummins ISB6.7 CM2350 (2013-17) Fault Code: 4152 PID: SPN: 5743 FMI: 9 Aftertreatment Selective Catalytic Reduction Temperature Sensor Module- Abnormal Update Rate - EcuForce TruckCummins ISB6.7 CM2350 (2013-17) Fault Code: 6647 PID: SPN: 6780 FMI: 3 Aftertreatment 1 Diesel Particulate Filter Soot Temperature Sensor - Voltage Above Normal Or Shorted To High Source. An Internal Circuit Error Has Been Detected By The Aftertreatment P $61.00Add to cart
- DOWNLOAD CAT ET 2021A (Caterpillar Electronic Technician) + Factory Password (1 PC )
$64.00Add to cart
- Related Products
Quick View
Add to wishlist
CompareAdd to cart
AllisonDTC TRUCKS
Quick View
Add to wishlist
CompareAdd to cart
AllisonDTC TRUCKS
Quick View
Add to wishlist
CompareAdd to cart
AllisonDTC TRUCKS
Quick View
Add to wishlist
CompareAdd to cart
AllisonDTC TRUCKS
Quick View
Add to wishlist
CompareAdd to cart
AllisonDTC TRUCKS
JPRO
DOWNLOAD Noregon JPRO Commercial Fleet Diagnostics 2017 v3 (Copy)$40.00Add to cart
cummisznn
Cumminmms Insite pro 8.9 Diagnostic Software$80.00Add to cart
Trucks software
JPRO Diagnostic Software Download 2024$100.00Add to cart
Trucks software
AGCO EDT 2023.10 Electronic Diagnostic Tool 1.125$120.00Add to cart
Trucks software
DOOSAN diagnostic software DMS-5 3.1.3 [2023.11] 1PC$106.00Add to cart
Trucks software
Bendix Acom Pro 2023 V1 diagnostic software 1PC$83.00Add to cart
Trucks software
VOLVOUU PTT TECH TOOL 2.8.220 2023 Last version 1pc$200.00Add to cart
Trucks software
Download Allison Doc Premium Update 2023 v2$105.00Add to cart
Hino
DOWNLOAD Hino DX3 Software 1.22.10 2022 ( 1 PC )$86.00Add to cart
DAF
SERVICE MANUALDAF xf xe engine manual$45.00Add to cart
TRUCK MANUALS
DOWNLOAD VOLVOUU I-Shift service manual PDF$55.00Add to cart
FUSO
$45.00Add to cart
DEUTZ
MANUAL SERVICE DEUTZ AGROTRON 230-260$45.00Add to cart
DEUTZ
MANUAL SERVICE DEUTZ AGROTRON 80-85-90-100-105 MK3$45.00Add to cart
BENDIX
SERVICE MANUAL BENDIX EC-60$45.00Add to cart
TRUCK MANUALS
SERVICE MANUAL 3000 and 4000 Series Gen 5 ALLISON$45.00Add to cart